Exhibitor List
| Company | JIANGSU MUSE ENVIRONMENTAL PROTECTION TECHNOLOGY CO.,LTD |
| Country | China |
| Products | Dust removal Treatment of volatile organic compounds（VOCs) Desulphurization and denitrification Synergistic governance of multiple pollutants Ultra low emission technology Odour treatment Noise and Vibration Control |
| Hall | 6 |
| Booth | A25 |
| Website | www.dfmuse.com |
| Introduction | The main products of Jiangsu Muse Environmental Protection Technology Co., Ltd. are activated carbon adsorption + CO catalytic combustion, spray booth + waste gas treatment, dust purification treatment equipment, shot blasting equipment. It is a professional production enterprise integrating R & D, design, manufacturing and installation. It can design and manufacture various non-standard special machinery according to the user's products. The company has strong technical force, complete production equipment and reliable product quality. |
Products
| Activated carbon adsorption + CO catalytic combustion Adsorption purification principle of organic waste gas After the organic waste gas is led out from the air duct, it enters the dry filter to remove the particulate matter and dust, and then enters the activated carbon adsorption bed. The number of adsorption beds is determined according to the air volume. The gas can be switched through the valve to make the gas enter different adsorption beds. The adsorption bed works alternately. After the gas enters the adsorption bed, the organic matter in the gas is adsorbed by the activated carbon and attached to the surface of the activated carbon, So that the gas can be purified, and the purified gas is discharged to the atmosphere through the fan. Principle of activated carbon regeneration unit By controlling the flow rate of desorption process, the concentration of organic waste gas can be concentrated 10-20 times. The desorbed gas flows through the electric heating device in the catalytic bed and is heated to about 300 ℃. Under the action of catalyst, it starts to burn. The purification efficiency of catalytic combustion process can reach more than 97%. After combustion, CO2 and H2O are generated and a large amount of heat is released. Part of the heat is used to heat the desorbed gas through the heat exchanger in the catalytic combustion bed The attached high concentration waste gas and another part of the air outside the heating chamber are used as active carbon desorption gas. Generally, the electric heater must be started for about 1 hour to achieve the self balance process of desorption catalytic combustion. When the heat balance is reached, the electric heating device can be shut down. The regeneration system relies on the organic solvent in the waste gas as fuel, which makes the regeneration process achieve self balance cycle without additional energy, greatly reducing energy consumption and no secondary pollution. The whole set of adsorption and catalytic combustion process is automatically controlled by PLC. |
 |
| Spray booth + waste gas treatment (catalytic combustion) Product introduction Spray booth, as the name suggests, is in a relatively closed space for filtering spray painting object painting coloring treatment. Also known as sub dust-free spray booth. Spray booth is the equipment that provides the special environment for painting operation, which can meet the requirements of temperature, humidity, illumination, air cleanliness, etc. during painting operation; it can limit and discharge the paint mist and organic waste gas generated during painting operation, which is an environmental protection coating equipment. working principle The external fresh air is filtered by the primary filter cotton at the air inlet and then sent to the static pressure chamber inside the roof by the forced draft fan. The air enters the static pressure chamber and is evenly sent to the operation room of the spray painting room after pressure equalizing and filtering by the sub efficient filter cotton. The air curtain is formed around the workpiece in laminar flow state. At this time, the no-load wind speed in the spray painting room can reach more than 0.3m/s, and the over spray mist generated during spray painting will not be in the operation room At this time, the concentration of harmful gases in the paint room is far lower than the maximum allowable concentration of harmful substances in the air of tj36-79 workshop, which is the national hygienic standard for the design of industrial enterprises. Then, under the action of exhaust fan, the airflow flows through the dry paint mist filtration system to the exhaust duct, and reaches the elevation after dry filtration + activated carbon adsorption treatment + catalytic combustion The exhaust gas meets the national standard. |
 |
| Inclined Cartridge Filter Inclined cartridge filter is a new type of high-efficiency dust collector newly developed by our company. Its core dust removal component is the filter cartridge, because the structure of the filter cartridge is the folded structure of the filter cloth. Compared with the ordinary bag filter, the filter cartridge filter has the advantages of better dust removal effect and smaller floor area, and its dust removal effect can even reach the dust emission concentration of 10mg / m3. 1. The advanced flow type layout and inclined structure of filter cartridge are adopted, so the dust remover has good effect of synchronous dust cleaning in the working process 2. The dust baffle is set at the dust gas inlet, which has the function of buffering and abrasion resistance, and does not make the dust directly impact the filter cartridge at high speed, so it can prolong the service life of the filter cartridge. The 15 ° inclined drawer type installation of the filter cartridge can make the removal and replacement of the filter cartridge more convenient, and the dust collector body is not provided with transmission parts, which reduces the maintenance work to the minimum. For general dust, the filter cartridge can be used for a long time without replacement, which saves the tedious work of frequently changing and washing the filter bag of common bag filter, and saves a lot of maintenance costs 4. Modular combination, size can be selected at will 5. The original combination can be expanded and the dust removal unit can be added without too much modification to the original equipment working principle After the dust gas enters the dust collector under the guidance of the fan, due to the sudden expansion of the air flow end face and the effect of the air flow distribution plate, part of the coarse dust particles in the air flow settle into the ash hopper under the action of gravity and inertial force; the fine dust particles with small density enter the filter chamber, and the dust deposits on the surface of the filter material through the comprehensive effects of brown diffusion and fiber interception The purified gas enters the clean gas chamber and is discharged by the air outlet through the fan. The resistance of the cartridge filter increases with the increase of the surface area of the cartridge. When the resistance reaches a certain set value, a high-speed and high-pressure air flow is ejected through the small hole of the injection pipe through the pulse valve of the reverse blowing system to clean the dust. At this time, the PLC program controls the opening and closing of the pulse valve. When the pulse valve is opened, the compressed air in the air bag evenly enters into the filter barrel through the expansion of the venturi tube, and forms an instantaneous positive pressure inside the filter barrel, resulting in huge vibration. The dust deposited on the filter material falls off and falls into the ash hopper. The collected dust is discharged into the ash bucket through the ash discharge valve. |
 |
| Venturi Wet Dust Collector Product introduction The wet dust collector has the advantages of high efficiency, simple structure, low cost, small floor area, convenient operation and maintenance, and is especially suitable for the treatment of high temperature, high humidity, flammable and explosive dust gas. In addition, some gaseous pollutants can be removed at the same time of dust removal. Therefore, it is widely used in air pollution control and gas purification of various departments of industrial production, especially for dust collection and purification of fire and explosion prevention. Wet dust collector can be divided into spray type, self-excited type, spray type and other types. This product adopts water spray design. This design is a kind of tooling equipment used for filtering and cooling the flue gas collected in the furnace and ash workshop. It is mainly used for collecting, filtering and cooling the dust and high-temperature flue gas generated in the production workshop, so as to reduce the emission pollution of dust and flue gas. |
 |